Best Quality 400-201 Exam Dumps 2021

We provide 400 201 dumps which are the best for clearing 400-201 test, and to get certified by Cisco CCIE SP Written v4.0. The 400 201 dumps covers all the knowledge points of the real 400-201 exam. Crack your Cisco 400-201 Exam with latest dumps, guaranteed!

Check 400-201 free dumps before getting the full version:

NEW QUESTION 1
An operation engineer from AS 2000 must deploy this inbound routing policy:
*Based on RFC 1998, modify the local-preference value for prefixes containing BGP community values 2000:90 and 2000:110
*Strip any BGP community of the BGP prefixes received from customers that are in the range between 2000:1 and 2000:2000. Any other BGP community values must not be removed
*Apply 2000:1003 BGP community Value, which indicates that the BGP prefix is learned form a customer
Which configuration accomplishes this BGP routing policy?
400-201 dumps exhibit

  • A. Option A
  • B. Option B
  • C. Option C
  • D. Option D

Answer: C

NEW QUESTION 2
Which two statements about 10 Gigabit Ethernet (10GE) are true? (Choose two.)

  • A. 10 Gigabit Ethernet does not support VLAN definition
  • B. 10 Gigabit Ethernet supports full duplex links, but does not support half duplex links.
  • C. 10 Gigabit Ethernet supports unshielded or shielded twisted-pair cable connections
  • D. 10 Gigabit Ethernet supports Carrier Sense Multiple Access with Collision Detection (CSMA/CD).
  • E. 10 Gigabit Ethernet supports optical fiber connections in single mode onl
  • F. Multi mode is not supported.

Answer: BC

NEW QUESTION 3
A network architect is tasked to design and deploy multicast in a service provider core. There is a requirement to have two PIM RP routers for PIM-SM distribute mode. What can the network architect do to satisfy this requirement?

  • A. Set two RPs with same priority.
  • B. Set two RPs, one with high priority and the other with low priority.
  • C. Set one RP as the main RP and another as a backup RP.
  • D. Set the RP-BSR method with one high-priority RP and one low-priority RP.

Answer: D

NEW QUESTION 4
A network engineer wants customers to retain routing information and Layer 2 connectivity for non-Ethernet VPNs within their networks. Which two technologies can be used to accomplish this goal? (Choose two.)

  • A. VPLS
  • B. L2TPv3
  • C. L3VPN
  • D. AToM
  • E. IPsec

Answer: BD

NEW QUESTION 5
Which component does NSF rely on to ensure that interfaces remain up during switchover and that lower layer protocol state is maintained?

  • A. SSO
  • B. BFD
  • C. IP FRR
  • D. LFA

Answer: A

NEW QUESTION 6
In an OSPF domain, four routers have OSPF neighborship over a broadcast domain. What is the expected state after running the show ip OSPF neighbor command on the OSPF designated router?

  • A. one FULL state, two 2WAY states
  • B. two FULL states, one 2WAY state
  • C. three FULL states
  • D. three 2WAY states

Answer: C

NEW QUESTION 7
An Enterprise XYZ company has a requirement to extend the MPLS/Layer 3 VPN MAN network to the remote branches using Internet as the transport. Which solution can you provide seamless extension of the MPLS/Layer 3 VPN?

  • A. LISP
  • B. L2TPv3
  • C. Cisco Unified MPLS
  • D. 2547oDMVPN
  • E. Carrier Supporting Carrier

Answer: D

NEW QUESTION 8
Select the three best answers which best describe Private Network-to Network Interface (PNNI) in an ATM network (Choose three.)

  • A. It is the Routing protocol used between ATM switches
  • B. PNNI uses the same Dijsktra algorithm for SPF calculation
  • C. PNNI and OSPF use the same Database to make cohesive decision for packet forwarding
  • D. PNNI measures line capacities and delays in addition to simple cost metrics

Answer: ABD

Explanation: The Private Network-to-Network Interface (PNNI) is a link-state routing protocol used in ATM networks. PNNI is similar to the open shortest path first (OSPF) used for IP routing. PNNI is a suite of network protocols that can be used to discover an ATM network topology, create a database of topology information, and route calls over the discovered topology. PNNI is a link-state routing protocol, which means that the protocol collects
information about the current state of links and nodes in the network to build a network database. The PNNI network database can be used to determine the network structure and the current state of network components. To build the PNNI network database, each PNNI node must receive topology information from all the other devices in the network. To keep the database current, the node must receive regular updates from other nodes.

NEW QUESTION 9
What is the main goal of the incident management?

  • A. Restore a normal service operation as quickly as possible
  • B. Create possible workarounds for issues that might recur
  • C. Enable the cursor to report issues
  • D. Ensure that the same incident does not recur

Answer: A

NEW QUESTION 10
Which E3 alarm indicates that there could be an issue with the transmit signal with the local equipment?

  • A. rxLoS
  • B. rxLoF
  • C. rxRAI
  • D. txRAI
  • E. txLoF
  • F. txLoS

Answer: C

NEW QUESTION 11
Refer to the exhibit. The P1 router is elected as the DIS on the broadcast link. Assuming that all the configurations are applied correctly, how many routers will establish IS-IS neighborship with P1 router on this broadcast link?

  • A. 1
  • B. 2
  • C. 3

Answer:

NEW QUESTION 12
Which Cisco IOS XR Virtualization technology provides full isolation between virtualized routing instances for extra control plane resources?

  • A. HVR
  • B. SVR
  • C. SDR
  • D. DRP

Answer: C

NEW QUESTION 13
According to RFC 3931, L2TPv3 utilizes the IANA assigned IP protocol ID of:

  • A. 110
  • B. 101
  • C. 121
  • D. 51
  • E. 151
  • F. 115

Answer: F

Explanation: IP Protocol 115 (L2TPv3)

NEW QUESTION 14
Refer to the exhibit.
400-201 dumps exhibit
R1 and R2 have a static default route that is configured to point toward the ISP. Both R1 and R2 routers redistribute the default route into OSPF. R2 is the primary gateway toward the ISP and R1 is the backup gateway. All link metrics are the same. Which two steps ensure that traffic to the ISP flows through R2 when the network works properly? (Choose two.)

  • A. Modify the preference value of the default route on R1 so that it is less preferred than OSPF external routes.
  • B. Modify the preference value of the default route on R2 so that it is less preferred than OSPF external routes.
  • C. Redistribute the default route as a type 1 external route on R1 and a type 2 external route on R2.
  • D. Redistribute the default route as a type 2 external route on R1 and a type 1 external route on R2.
  • E. Redistribute the default route on R1 with a higher metric than the existing metric of the distributed default route on R2.

Answer: AD

NEW QUESTION 15
Refer to the exhibit.
400-201 dumps exhibit
There are receivers that are registered at the RP. If the source begins sending multicast traffic toward R1, how will R1 handle that traffic?

  • A. R1 forwards the multicast packets on the (S, G) tree toward the RP.
  • B. R1 encapsulates the multicast packets into a PIM register multicast packet.
  • C. R1 encapsulates the multicast packets into a PIM join unicast packet.
  • D. R1 tunnels the multicast packets in PIM register messages toward the RP.

Answer: D

NEW QUESTION 16
Which two components does the LDP use to discover neighbors on a network segment? (Choose two)

  • A. 224.0.0.14 multicast address
  • B. 224.0.0.1 multicast address
  • C. 224.0.0.2 multicast address
  • D. 711 tcp port
  • E. 646 udp port
  • F. 711 udp port
  • G. 646 tcp port

Answer: CE

Thanks for reading the newest 400-201 exam dumps! We recommend you to try the PREMIUM 2passeasy 400-201 dumps in VCE and PDF here: https://www.2passeasy.com/dumps/400-201/ (699 Q&As Dumps)