It is more faster and easier to pass the CheckPoint 156-915.77 exam by using Guaranteed CheckPoint Check Point Certified Security Expert Update Blade questuins and answers. Immediate access to the Updated 156-915.77 Exam and find the same core area 156-915.77 questions with professionally verified answers, then PASS your exam with a high score now.
Free demo questions for CheckPoint 156-915.77 Exam Dumps Below:
NEW QUESTION 1
You are troubleshooting a HTTP connection problem. You've started fw monitor -o http.pcap. When you open http.pcap with Wireshark there is only one line. What is the most likely reason?
- A. fw monitor was restricted to the wrong interface.
- B. Like SmartView Tracker only the first packet of a connection will be captured by fw monitor.
- C. By default only SYN pakets are captured.
- D. Acceleration was turned on and therefore fw monitor sees only SYN.
Answer: D
NEW QUESTION 2
MultiCorp has bought company OmniCorp and now has two active AD domains. How would you deploy Identity Awareness in this environment?
- A. You must run an ADquery for every domain.
- B. Identity Awareness can only manage one AD domain.
- C. Only one ADquery is necessary to ask for all domains.
- D. Only Captive Portal can be used.
Answer: A
NEW QUESTION 3
Match the following commands to their correct function.
Each command has one function only listed.
- A. C1>F6; C2>F4; C3>F2; C4>F5
- B. C1>F2; C2>F1; C3>F6; C4>F4
- C. C1>F2; C2>F4; C3>F1; C4>F5
- D. C1>F4; C2>F6; C3>F3; C4>F2
Answer: A
NEW QUESTION 4
What is the purpose of the pre-defined exclusions included with SmartEvent R77?
- A. To allow SmartEvent R77 to function properly with all other R71 devices.
- B. To avoid incorrect event generation by the default IPS event definition; a scenario that may occur in deployments that include Security Gateways of versions prior to R71.
- C. As a base for starting and building exclusions.
- D. To give samples of how to write your own exclusion.
Answer: B
NEW QUESTION 5
How can you check whether IP forwarding is enabled on an IP Security Appliance?
- A. clish -c show routing active enable
- B. cat /proc/sys/net/ipv4/ip_forward
- C. echo 1 > /proc/sys/net/ipv4/ip_forward
- D. ipsofwd list
Answer: D
NEW QUESTION 6
Select the correct statement about Secure Internal Communications (SIC) Certificates. SIC Certificates:
- A. Are used for securing internal network communications between the SmartDashboard and the Security Management Server.
- B. For R75 Security Gateways are created during the Security Management Server installation.
- C. Decrease network security by securing administrative communication among the Security Management Servers and the Security Gateway.
- D. Uniquely identify Check Point enabled machines; they have the same function as VPN Certificates.
Answer: D
NEW QUESTION 7
CORRECT TEXT
Fill in the blanks. To view the number of concurrent connections going through core 0 on the firewall, you would use the command and syntax _____.
Solution:
fw –i 0 tab –t connections –s
Does this meet the goal?
- A. Yes
- B. Not Mastered
Answer: A
NEW QUESTION 8
Many companies have defined more than one administrator. To increase security, only one administrator should be able to install a Rule Base on a specific Firewall. How do you configure this?
- A. Define a permission profile in SmartDashboard with read/write privileges, but restrict it to all other firewalls by placing them in the Policy Targets fiel
- B. Then, an administrator with this permission profile cannot install a policy on any Firewall not listed here.
- C. Put the one administrator in an Administrator group and configure this group in the specific Firewall object in Advanced > Permission to Install.
- D. In the object General Properties representing the specific Firewall, go to the Software Blades product list and select Firewal
- E. Right-click in the menu, select Administrator to Install to define only this administrator.
- F. Right-click on the object representing the specific administrator, and select that Firewall in Policy Targets.
Answer: B
NEW QUESTION 9
Match the ClusterXL modes with their configurations. Exhibit:
- A. A-2, B-3, C-4, D-1
- B. A-2, B-3, C-1, D-5
- C. A-3, B-5, C-1, D-4
- D. A-5, B-2, C-4, D-1
Answer: C
NEW QUESTION 10
You enable Hide NAT on the network object, 10.1.1.0 behind the Security Gateway’s external interface. You browse to the Google Website from host, 10.1.1.10 successfully. You enable a log on the rule that allows 10.1.1.0 to exit the network. How many log entries do you see for that connection in SmartView Tracker?
- A. Two, one for outbound, one for inbound
- B. Only one, outbound
- C. Two, both outbound, one for the real IP connection and one for the NAT IP connection
- D. Only one, inbound
Answer: B
NEW QUESTION 11
Which is the lowest Gateway version manageable by SmartCenter R77?
- A. R65
- B. S71
- C. R55
- D. R60A
Answer: A
NEW QUESTION 12
Which process should you debug if SmartDashboard login fails?
- A. sdm
- B. cpd
- C. fwd
- D. fwm
Answer: D
NEW QUESTION 13
CORRECT TEXT
Fill in the blanks. To view the number of concurrent connections going through your
firewall, you would use the command and syntax_______
Solution:
fw tab –t connections –s
Does this meet the goal?
- A. Yes
- B. Not Mastered
Answer: A
NEW QUESTION 14
CORRECT TEXT
Fill in the blank. The command that typically generates the firewall application, operating system, and hardware specific drivers is .
Solution:
snapshot
Does this meet the goal?
- A. Yes
- B. Not Mastered
Answer: A
NEW QUESTION 15
A ClusterXL configuration is limited to members.
- A. There is no limit.
- B. 16
- C. 6
- D. 2
Answer: C
NEW QUESTION 16
Which command would provide the most comprehensive diagnostic information to Check Point Technical Support?
- A. fw cpinfo
- B. cpinfo -o date.cpinfo.txt
- C. diag
- D. cpstat - date.cpstat.txt
Answer: B
NEW QUESTION 17
How many pre-defined exclusions are included by default in SmartEvent R77 as part of the product installation?
- A. 5
- B. 10
- C. 3
Answer: D
NEW QUESTION 18
Your R77 primary Security Management Server is installed on GAiA. You plan to schedule the Security Management Server to run fw logswitch automatically every 48 hours. How do you create this schedule?
- A. On a GAiA Security Management Server, this can only be accomplished by configuring the command fw logswitch via the cron utility.
- B. Create a time object, and add 48 hours as the interva
- C. Open the primary Security Management Server object’s Logs and Masters window, enable Schedule log switch, and select the Time object.
- D. Create a time object, and add 48 hours as the interva
- E. Open the Security Gateway object's Logs and Masters window, enable Schedule log switch, and select the Time object.
- F. Create a time object, and add 48 hours as the interva
- G. Select that time object’s Global Properties > Logs and Masters window, to schedule a logswitch.
Answer: B
NEW QUESTION 19
......
Recommend!! Get the Full 156-915.77 dumps in VCE and PDF From Dumps-files.com, Welcome to Download: https://www.dumps-files.com/files/156-915.77/ (New 203 Q&As Version)